PANASONIC PROJECTOR TX310EA

PANASONIC PROJECTOR TX310EASPESIFIKASI PANASONIC PROJECTOR TX310EA :

Power supply 100-240 V AC, 50/60 Hz
Power consumption 300 W (0.5 W when STANDBY MODE set to ECO,*1
6.0 W when STANDBY MODE set to NORMAL.)
LCD panel Display method Transparent LCD panel (x 3, R/G/B)
Drive method Active matrix method
Panel size 16.0 mm (0.63 in) (4:3 aspect ratio)
Pixels 786,432 (1,024 x 768) pixels
Lens Fixed (0.46:1 throw ratio), manual focus F = 1.8, f = 6.08 mm
Lamp 230 W x 1,
lamp replacement cycle (lamp control: Normal/Eco1/Eco2): 5,000 hours/6,000 hours/8,000 hours*2
Screen size (diagonal) 1.27-2.54 m (50-100 in), 4:3 aspect ratio
Brightness*3
(Lamp power: Normal)
3,200 lm
Center-to-corner uniformity*3 80 %
Contrast*3 10,000:1 (full on/off)
(RGB signal input, Color mode: Dynamic, Lamp power: Normal)
Resolution 1,024 x 768 pixels
(Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.)
Scanning frequency HDMI fH: 15-91 kHz, fV: 24-85 Hz, dot clock: 162 MHz or lower
RGB (analog) fH: 15-91 kHz, fV: 24-85 Hz, dot clock: 162 MHz or lower
YPBPR(YCBCR) fH: 15.73 kHz, fV: 59.94 Hz [480i (525i)],
fH: 15.63 kHz, fV: 50 Hz [576i (625i)],
fH: 45.00 kHz, fV: 60 Hz [720 (750)/60p],
fH: 33.75 kHz, fV: 60 Hz [1080 (1125)/60i],
fH: 28.13 kHz, fV: 25 Hz [1080 (1125)/25p],
fH: 27.00 kHz, fV: 48 Hz [1080 (1125)/24sF],
fH: 67.50 kHz, fV: 60 Hz [1080 (1125)/60p],
fH: 31.47 kHz, fV: 59.94 Hz [480p (525p)],
fH: 31.25 kHz, fV: 50 Hz [576p (625p)],
fH: 37.50 kHz, fV: 50 Hz [720 (750)/50p],
fH: 28.13 kHz, fV: 50 Hz [1080 (1125)/50i],
fH: 27.00 kHz, fV: 24 Hz [1080 (1125)/24p],
fH: 33.75 kHz, fV: 30 Hz [1080 (1125)/30p],
fH: 56.25 kHz, fV: 50 Hz [1080 (1125)/50p]
Video/S-Video fH: 15.73 kHz, fV: 59.94 Hz [NTSC/NTSC4.43/PAL-M/PAL60],
fH: 15.63 kHz, fV: 50 Hz [PAL/SECAM/PAL-N]
Optical axis shift 21:1 (fixed)
Keystone correction range Vertical: ±15° (Auto, Manual), horizontal: ±15° (Manual)
Installation Ceiling/floor, front/rear
Terminals HDMI IN HDMI 19-pin x 1 (compatible with HDCP, Deep Color)
480i,*4 480p, 576i,*4 576p, 720/60p, 720/50p, 1080/60i, 1080/50i,
1080/60p, 1080/50p, 1080/30p, 1080/25p, 1080/24p, 1080/24sF,
VGA (640 x 480)-WUXGA (1,920 x 1,200),*5
audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz)
COMPUTER 1 IN D-sub HD 15-pin (female) x 1 (RGB/YPBPR/YCBCR /S-VIDEO x 1)
(The D-Sub/S-VIDEO conversion cable ET-ADSV is required for inputting S-VIDEO signals.)
COMPUTER 2 IN/
MONITOR OUT
D-sub HD 15-pin (female) x 1 (RGB x 1), (input/output selectable using on-screen menu)
MONITOR OUT
VIDEO IN Pin jack x 1
AUDIO 1 IN M3 x 1 (L-R x 1)
AUDIO 2 IN Pin jack x 2 (L, R x 1)
AUDIO OUT M3 x 1 (L-R x 1) for output (variable)
LAN RJ-45 x 1
(for network connection, 10BASE-T/100BASE-TX, compliant with PJLink (class 1))
SERIAL IN D-sub 9-pin (female) x 1 for external control (RS-232C compliant)
USB A USB type-A (for the Memory Viewer) x 1
USB B USB type-B (for the USB Display) x 1
Built-in speaker 10 W (monaural) x 1
Cabinet materials Molded plastic (PC)
Dimensions (W x H x D) 335 x 134.1*6 x 329 mm (13-3/16 x 5-9/32*6 x 12-15/16 in)
Weight*7 Approximately 3.8 kg (8.4 lbs)
Operation noise*3 37 dB (Lamp power: Normal), 33 dB (Lamp power: Eco1), 28 dB (Lamp power: Eco2)
Operating temperature 5°C-40°C (41°F-104°F) (less than 1,400 m [4,593 ft] above sea level),
5°C-35°C (41°F-95°F) (between 1,400 m and 2,700 m [4,593 ft and 8,858 ft] above sea level)
Operating humidity 20-80 % (no condensation)
Supplied accessories Power cord x 1*8,
Wireless remote control unit x 1,
Batteries (AAA/R03/LR03 type x 2),
Computer cable (1.5 m, for VGA) x 1,
Software CD-ROM (Multi Projector Monitoring & Control Software) x 1
NOTE * Product numbers vary depending on the market. The general guideline is as follows:
The product number in Europe (except the UK) and CIS is PT-TX400E and PT-TX310E.
The product number in the UK, Asia (except Taiwan), Oceania, Middle East, and Africa is PT-TX400A, PT-TX310A and PT-TX210A.
*1 When the Standby mode is set to Eco, network functions such as power on over the LAN network will not operate.
Also, only certain commands can be received for external control using the serial terminal.
*2 The value for the recommended lamp replacement cycle is the maximum value, at which luminance will become 50 %.
The usage environment affects the duration of the lamp.
*3 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*4 Only compatible with dot clock frequency of 27 MHz (pixel repetition signal).
*5 Compliant with VESA CVT-RB.
*6 With legs at shortest position.
*7 The above values are averages. Actual values may be different according to the product.
*8 Power cord (x2) for the PT-TX400A/TX310A/TX210A.
Please follow and like us:
0